This 2 channel high duty radio remote controller has the special ability to learn remote codes, allowing it to be used in one-transmitter-to-many-receivers system. It operates in toggle, momentary and latched mode (set the mode as you like freely). It is great for hard to reach lights or other DC/AC electrical devices. Widely used for gate / motor / garage door / light remote control and so on.
Control Lights, Motors, Fans, electrically operated Doors/Locks/Windows/Blinds/Cars or Other Appliances with AC110~240V or DC0~28V.
You can turn on/off the receiver with transmitter (remote control) from any place within a reliable distance; the wireless RF signal can pass through walls, floors and doors.
With characteristics of reverse power protection and over current protection
Audible / visual indication
Use microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology.
Reliable control: The transmitter (Encoding) and the receiver (Decoding) use an 8-bit code.
One/ several transmitters can control one/ several receivers simultaneously.
If you use two or more receivers in the same place, you can set them with different codes.
Transmitting Frequency: 315MHz / 433MHz
Receiver:
Model No.: S1PU-DC12 / S1PU-DC24
Channel: 1 CH
Control Mode: Toggle, Momentary, Latched
Coding Type: Learning code
Coding Setting: By learning
Power Supply (Operating Voltage): DC12V±1V (S1PU-DC12), DC24V±1V (S1PU-DC24)
PCB Size: 74mm x 52mm x 24mm
Case Size: 79mm x 58mm x 35mm
Maximum Working Current: 30A
Transmitter:
Model No.: C-2
Channel: 2 CH
Remote Control Distance: 100m / 300ft (theoretically)
Encode: Fixed code by soldering
Unit size: 58mm x 39mm x 16mm
Power Supply: 1 x 23A -12V battery (included, can be used for 12 months)
Usage:
Setting control mode Toggle: Only connect Jumper-1. Control mode Toggle: Press -> On; Press again -> Off. Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C) Press button 1 again: Turn off the relay (disconnect A and B, connect A and C) Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C) Press button 2 again: Turn off the relay (disconnect A and B, connect A and C)
Setting control mode Momentary: Only connect Jumper-2. Control mode Momentary: Press and hold -> On; Release -> Off. Press and hold button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C) Release button 1: Turn off the relay (disconnect A and B, connect A and C) Press and hold button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C) Release button 2: Turn off the relay (disconnect A and B, connect A and C)
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2. Control mode Latched: Press -> On, other relays Off; Press another button -> Off. Press button 1: Turn on the relay of the receiver 1 (connect A and B, disconnect A and C) Turn off the relay of the receiver 2 (disconnect A and B, connect A and C) Press button 2: Turn on the relay of the receiver 2 (connect A and B, disconnect A and C) Turn off the relay of the receiver 1 (disconnect A and B, connect A and C)
Package Include:
2 x Receiver: S1PU-DC12 / S1PU-DC24 (1 Channel / Three Control Modes)
2 x Transmitter: C-2
1 x User manual
Note:
The theoretical distance is 100m, which shall be operated in an open ground; no barriers and no any interference. But in actual operation, it is hindered by trees, walls or other obstacles, or interfered by other signals. Therefore, the actual distance can not reach 100m. If you need longer range, please choose other series of remote control, such as CB Serie (1000m/3000ft) - Click here; Or you can add the External Extend Antenna (model: 0020909) on the receiver to extend the range - Click here.
