Log In     My Account       Shopping Cart: Your cart is empty.

Currencies:
     English  



Home >>  DC Power Remote Kits >>  16CH DC Power Remote Kits >>  16 Channel / Normally open and normally closed Relay DC 9V / 12V / 24V RF Receiver - 16 Control Mode

Remote Control Blog

16 Channel / Normally open and normally closed Relay DC 9V / 12V / 24V RF Receiver - 16 Control Mode


Price: US $70.00

Add to Cart:   

  • Model: 0020089 (S16C-DC09 / 12 / 24+1CV-16)

Please Choose:





















     
  
 Manuel

Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
Wireless control, easy to install.
Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminals are NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to equipments.
Each channel can work at maximum current 10A, such as 120W/12V, 60W/6V, 90W/9V, 240W/24V, 1100W/110V, 2200W/220V.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Working Range:
With a transmitter (such as CV-16) to form a complete set, the maximum working distance can reach 500M in an open ground. 
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters.

Receiver Parameters:
Model No.: S16C-DC09 / S16C-DC12 / S16C-DC24
Power Supply (Operating Voltage): DC12V±1V (S16C-DC12), DC9V±1V (S16-DC09), DC24V±2V (S16C-DC24)
Working Frequency: 315MHz / 433MHz
Channel: 16CH
Control Modes: Toggle, Momentary, Latched, Toggle + Momentary
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Maximum Working Current of Relay: 10A / each channel
Static Current: ≤6mA
PCB size: 117mm x 73mm x 16mm

Matching Transmitters:
The receiver can work with different transmitters, such as model CV-16 (500M), C-1 (100M), CWB-1 (50M, waterproof), CP-1 (500M), or CB-1 (1000M) etc. 

Usage (with the transmitter CV-16):
The receiver can be used to control both DC 0~28V and AC 110~240V equipments.

Notice: The receiver is relay output, not DC/AC power output. The terminals are NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to equipments.
Initial state of relay output terminals: Terminals A and B are Normally Open; Terminals B and C are Normally Closed. 

Wiring:
If you want to control the DC 12V lamps, do as following:
1) Connect the positive pole of DC power supply to terminal “+”, and connect the negative pole of DC power supply to terminal “ -”.
2) Connect terminal A to the positive pole of DC power supply, connect terminal B to the positive pole of DC lamp, and connect the negative pole of DC lamp to the negative pole of DC power supply.

If you want to control the AC 220V lamps, do as following:
1) Connect the positive pole of DC power supply to terminal “+”, and connect the negative pole of DC power supply to terminal “ -”.
2) Connect terminal A to the live wire of AC power supply, connect terminal B to one side of AC lamp, and connect another side of AC lamp to the neutral wire of AC power supply.

Setting different control modes: (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as following operation):
1) Setting control mode Toggle: When the receiver is in the status of LEARNING, press button 1 of the remote control.
Control mode Toggle (Channel 1~16): Press -> On; Press again -> Off.
Press button 1: Turn on relay 1 (connect A and B, disconnect B and C), the lamp 1 is on.
Press button 1 again: Turn off relay 1 (disconnect A and B, connect B and C), the lamp 1 is off.
Press button 16: Turn on relay 16 (connect A and B, disconnect B and C), the lamp 16 is on.
Press button 16 again: Turn off relay 16 (disconnect A and B, connect B and C), the lamp 16 is off.

2) Setting control mode Momentary: When the receiver is in the status of LEARNING, press button 2 of the remote control.
Control mode Momentary (Channel 1~16): Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on relay 1 (connect A and B, disconnect B and C), the lamp 1 is on.
Release button 1: Turn off relay 1 (disconnect A and B, connect B and C), the lamp 1 is off.
Press and hold button 16: Turn on relay 16 (connect A and B, disconnect B and C), the lamp 16 is on.
Release button 16: Turn off relay 16 (disconnect A and B, connect B and C), the lamp 16 is off.

3) Setting control mode Latched: When the receiver is in the status of LEARNING, press button 3 of the remote control.
Control mode Latched (Channel 1~16): Press -> On, other relays Off; Press other button -> Off.
Press button 1: Turn on relay 1 (connect A and B, disconnect B and C), the lamp 1 is on. 
               Turn off other relays (disconnect A and B, connect B and C), other 15 lamps are off.
Press button 16: Turn on relay 16 (connect A and B, disconnect B and C), the lamp 16 is on.
Turn off other relays (disconnect A and B, connect B and C), other 15 lamps are off.

4) Setting control mode Toggle + Momentary: When the receiver is in the status of LEARNING, press button 4 of the remote control.
Control mode Toggle (Channel 1~8): Press -> On; Press again -> Off.
Press button 1: Turn on relay 1 (connect A and B, disconnect B and C), the lamp 1 is on.
Press button 1 again: Turn off relay 1 (disconnect A and B, connect B and C), the lamp 1 is off.
Press button 8: Turn on relay 8 (connect A and B, disconnect B and C), the lamp 8 is on.
Press button 8 again: Turn off relay 8 (disconnect A and B, connect B and C), the lamp 8 is off.
Control mode Momentary (Channel 9~16): Press and hold -> On; Release -> Off.
Press and hold button 9: Turn on relay 9 (connect A and B, disconnect B and C), the lamp 9 is on.
Release button 9: Turn off relay 9 (disconnect A and B, connect B and C), the lamp 9 is off.
Press and hold button 16: Turn on relay 16 (connect A and B, disconnect B and C), the lamp 16 is on.
Release button 16: Turn off relay 16 (disconnect A and B, connect B and C), the lamp 16 is off.

How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED flashes one time . The receiver enters into status of LEARNING.
2) Press any one button on transmitter within 5 seconds. If signal LED flashes one time and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the learning button, signal LED turns off, learning process will be discontinued. 
4) The receiver can learn several remote controls with different codes.

Delete all transmitters:
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the learning button of receiver until signal LED turns on then off. That means all stored codes have been deleted successfully.

Package Include:
1 x Receiver:S16C-DC09 / S16C-DC12 / S16C-DC24
1 x Transmitter: CV-16
1 x User manual
Ask A Question
* Required information

*
*