Log In     My Account       Shopping Cart: Your cart is empty.

Currencies:
     English  



Home >>  DC Output Remote Kits >>  1 Channel Wireless Remote Control Switch DC Power Output

Remote Control Blog

1 Channel Wireless Remote Control Switch DC Power Output


Price: US $34.00

Add to Cart:   

  • Model: 0020424 (S1X-DC & C-2)

Please Choose:



































This 1 channel dc wireless remote control switch is with direct power output function. The input and output power are the same. Easier for wiring and operation. Widely applied to control lights, motors, fans, electrically operated doors / locks / windows or other electrical devices.
 
  Manual

Video: Wireless remote control Christmas tree

Feature:
Application: It can be used in industry automation, agriculture automation and home automation, such as factory, house, farm, pasture, vehicle, ship, offshore
operation, aerial vehicle, field call, etc. It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans,
winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.
DC Power Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.
With w
ired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Receiver Parameters:
Model No.: S1X-DC06 / S1X-DC09 / S1X-DC12 / S1X-DC24
Power Supply (Operating Voltage): DC6V (S1X-DC06), DC12V±1V (S1X-DC12), DC9V±1V (S1X-DC09), DC24V±1V (S1X-DC24)
Output: DC6V (
S1X-DC06), DC12V (S1X-DC12), DC9V (S1X-DC09), DC24V (S1X-DC24)
Working Frequency: 315MHz / 433MHz
Channel: 1 CH
Control Modes: Toggle, Momentary, Latched
Static Current: ≤6mA
Maximum Working Current: 10A
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Work with Fixed code transmitters or Learning code transmitters.

Terminal Parameters of receiver:
Wire range≤12 AWG
Temperature range: -40℃ ~ +105℃
Screw
M3

Transmitter Parameters:
Model No.: 0021001 (C-2)
With Sliding Cover: Slide up when it doesn’t work (to protect the button). Slide down the button will appear.
Shell Color: Wood Color / White/ Black
Channel/Button: 2
Button Symbol:1, 2
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 6mA
Operating Frequency: 315Mhz / 433Mhz
Encoding Chip: PT2262/ PT2264/ SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes.
Transmitting Distance: 100m / 300ft (theoretically)
The distance of 100m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or may not reach 100m.
If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 58mm x 39mm x 16mm
Weight: 30g
Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.
 
How to set up the 8-bits code of the transmitter:
1. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.
2. The upper row of pads is “L” side, and the lower row of pads is “H” side.
3. If solder the middle row of chip feet to the “L” side, it is code 1. If solder the middle row of chip feet to the “H” side, it is code 2. Don’t solder to any side, it is code 0.
4. The 8-bits code order is from left to right (from D1 to D8).
5. Here is an example, the 8-bits code in the picture is 01121101, solder as the following way:
6. Code 0: don’t solder any side, like D1 and D7.
7. Code 1: solder to the “L” side, like D2, D3, D5, D6, D8.
8. Code 2: solder to the “H” side, like D4.

 
Matching Transmitters:
The receiver can work with different transmitters, such as model C-1 / C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), CP-1 / CP-2 (500M), or CB-1 / CB-2 (1000M) etc.
When you set the receiver in toggle or momentary mode, it should work with
single button transmitter, such as model C-1 (100M), CWB-1 (50M, waterproof)CP-1 (500M), or CB-1 (1000M) etc. When you set the receiver in latched mode, it should work with two buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2 (500M), or CB-2 (1000M) etc.

Working Range:
With a transmitter (such as C-2) to form a complete set, the maximum working distance can reach 100M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximumworking distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters.

Usage:
The receiver can be used to control DC 6V / 9V / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you should choose the receiver with same DC 12V version; and if the power supply of those equipments is DC 24V, you should choose the receiver with same DC 24V version.

Wiring:
If you want to control a DC 12V lamp, do as following:
1) Connect the positive pole of DC power supply to terminal “L/+”, and connect the negative pole of DC power supply to terminal “N/-”.
2) Connect the positive pole of lamp to terminal " L/+" of OUT 1, and connect the negative pole of lamp to terminal " N/-" of OUT 1.

Setting different control modes
:
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as following operation):

Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (with the transmitter C-1): Press -> On; Press again -> Off.
Press the transmitter: Turn on the relay, terminal OUT 1 outputs DC power, the lamp is turned on.
Press the transmitter again: Turn off the relay, terminal OUT 1 stop outputting, the lamp is turned off.

Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with the transmitter C-1): Press and hold -> On; Release -> Off.
Press and hold the transmitter: Turn on the relay, terminal OUT 1 outputs DC power, the lamp is turned on.
Release the transmitter: Turn off the relay, terminal OUT 1 stop outputting, the lamp is turned off

Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched (with the transmitter C-2): Press button 1-> On, other relays Off; Press button 2 -> Off.
Press button 1: Turn on the relay, terminal OUT 1 outputs DC power, the lamp is turned on.
Press button 2: Turn off the relay, terminal OUT 1 stop outputting, the lamp is turned off.

Wired control terminals:
The receiver has wired control terminals, you can connect external devices, sensors, limit switches or manual switches to trigger the receiver.

1) By low level signal:
You can connect external devices (with low level output signal) to trigger the receiver.
When external device outputs low level signal to terminals 1 (Signal +) and terminal 3 (Signal -), t
erminal of OUT 1 output DC power, and the lamp is turned on.
When external device stops to output signal, terminal of OUT 1 stop outputting, and the lamp is turned off.

2) By NO/NC contact:
You can connect manual switches (with NO/NC contact) to trigger the receiver.
When connect terminals 1 and 3 by manual switch, t
erminal of OUT 1 output DC power, and the lamp is turned on.
When disconnect terminals 1 and 3 by manual switch, terminal of OUT 1 stop outputting, and the lamp is turned off.

Antenna difference
Fixed code remote control
Learning code remote control

Ask A Question
* Required information

*
*