Log In     My Account       Shopping Cart: Your cart is empty.

Currencies:
     English  



Home >>  DC Motor Remote Kits >>  100m DC Motor Wireless Control Receiver and transmitter

Remote Control Blog

100m DC Motor Wireless Control Receiver and transmitter


Price: US $45.00

Add to Cart:   

  • Model: 0020328 (S1FM-DC12+1C-2L-2)

Please Choose:


























Package Include:

1 x Receiver: S1FM-DC12
1 x Transmitter: C-2L-2
1 x User manual
 
Features:
Application: It can be used in rolling blinds, rolling doors, projection screens, awnings, pumps, winches, conveyors or other appliances and equipments with DC motors, it can remote control DC motor rotates in the positive or reversal direction.
Wireless control, easy to install.
You can rotate a motor in the positive or reversal direction with the transmitter (remote control) from any place within a reliable distance.
The RF wireless signal can pass through walls, floors and doors.
With limit control terminals: You can connect limit switches or sensors to stop the motor.
With wired control terminals: You can connect manual switches to control the motor.
You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance.
With reverse power protection and over current protection.
Reliable control: The receiver only works with the transmitter which use same code.
One/several transmitters can control one/several receivers simultaneously.
You can use two or more units in the same place.

Working Range:
With a transmitter (such as C-2L-2) to form a complete set, the maximum working distance can reach 100M in an open ground.
The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance.
If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters.

Receiver Parameters:
Model No: S1FM-DC12
Control Mode: Momentary
Power Supply (Operating Voltage): DC12V~36V
Output: DC12V~36V
Working Frequency: 315MHz / 433MHz
Channel: 1 CH, can work with 1 DC motor
Static Current: ≤6mA
Maximum Working Current: 10A / each channel, so motor's maximum starting current can not exceed 10A.
PCB Size: 94mm x 56mm x 24mm
Case Size: 100mm x 60.5mm x 30mm
Work with Fixed code transmitters
 
Transmitter Parameters:
Model No.: 0021125 (C-2L-2)
With Sliding Cover: Slide up when it doesn’t work (to protect the button). Slide down the button will appear.
Shell Color: Black
Channel/Button: 2
Button Symbol:▲▼
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 3mA
Operating Frequency: 315Mhz / 433Mhz
Encoding Chip: EV1527
Encoding Type: Learning code (up to 1 million codes, reducing code collision and unauthorized code scanning possibilities.)
Transmitting Distance: 100m / 300ft (theoretically)
The distance of 100m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or may not reach 100m.
If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be.
Modulation Mode: ASK
Operating Temperature: -20 ° C to +70 ° C
Unit Size: 58mm x 39mm x 16mm
 
Matching Transmitters:
This receiver can work with different transmitters. such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), CV-2-2 (500M), or CB-2 (1000M) etc.
 
Usage (with transmitter C-2L-2):
Connect the positive pole of DC power supply to terminal “+” of INPUT, and connect the negative pole of DC power supply to terminal “-” of INPUT.
Connect terminals “Motor” to motor, You can exchange motor's two wires to change the rotating direction of motor.
 
Setting different control modes:
Setting control mode Momentary: Connect Jumper 1&2
Press and hold button  on the transmitter: motor rotates in positive direction. Release button  on the transmitter: motor stops.
Press and hold button  on the transmitter: motor rotates in reversal direction. Release button  on the transmitter: motor stops.
 
Limit control terminals:
Limit control terminals TOPR, COM and TOPL are normally close, you can connect limit switches or sensors (normally close type) to TOPR, COM and TOPL, and then you can use limit switches or sensors to stop the motor.
When motor rotates in positive direction, if disconnect two terminals TOPR & COM, the motor will stop automatically.
When motor rotates reversal direction, if disconnect two terminals TOPL & COM, the motor will stop automatically.
 
Wired control terminals:
You can connect manual switches to terminals “COM”, “UP”, “Signal DOWN”, then you can use manual switches to control the motor.
When connect terminals “UP” and “COM”, motor rotates in positive direction. And when disconnect “UP” and “COM”, motor stops.
When connect terminals “DOWN” and “COM”, motor rotates in reversal direction. And when disconnect “DOWN” and “COM”, motor stops.
 
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2)Press and hold button  on remote control, signal LED flashes 2 times, release button ; then press and hold button  on remote control, signal LED flashes 2 times again, release button , signal LED is on; it means learning is successful. press the learning button of receiver, signal LED turns off, or restart the receiver.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
 
Delete all transmitters:
We have learned remote control to the receiver. If you don’t want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes 3 times then off; release the button. That means all stored codes have been deleted successfully.
Ask A Question
* Required information

*
*