Manual
Package Include:
1 x Receiver: S1PU-DC-ANT3
2 x Transmitter: C-1 / C-2
1 x User manual
Feature:
Application: It can be used in industry
automation, agriculture automation and home automation, such as
factory, house, farm, pasture, vehicle, ship, offshore operation,
aerial vehicle, field call, etc. It can remote control equipments on
land, water and air, such as remote control lights, sirens, locks,
motors, fans, winches, blinds, linear actuators, doors, windows,
electric solenoid valves, security alarm, business signs and various
devices.
Wireless control, easy to install.
Power Supply: Four working voltage versions, DC 6V, 9V, 12V, 24V.
Waterproof: The receiver has waterproof case and waterproof
connector, it can be installed outdoors.
Relay Output: This receiver is dry relay output, it can be used to
operate both DC and AC equipments. The output terminals are NO / NC
(normally open / normally closed), which serves as a switch. That
means you should also connect a separate power supply to equipments.
High Power: Each channel can work at maximum current 30A.
With wired control terminals: You can connect sensors, limit
switches, manual switches or external devices to control the
receiver.
With external telescopic antenna, the receiver have a farther
working range.
You can control the equipments by using the receiver with
transmitter (remote control) from any place within a reliable
distance.
Wireless RF signal can pass through walls, floors, doors or windows.
With characteristics of reverse power protection and over current
protection.
Reliable control: The code has thousands of different combinations,
and the receiver only works with the transmitter which use the same
code.
One/several transmitters can control one/several receivers
simultaneously.
You can use two or more units in the same place.
Receiver Parameters:
Model No.: S1PU-DC06-ANT3/ S1PU-DC09-ANT3 / S1PU-DC12-ANT3 /
S1PU-DC24-ANT3
Power Supply (Operating Voltage): DC6V (S1PU-DC06), DC9V±1V
(S1PU-DC09), DC12V±1V (S1PU-DC12), DC24V±2V (S1PU-DC24)
Output: Relay output (Normally open and normally closed)
Working Voltage Range of Relay: AC110~240V or DC0~28V
Wire range for the terminals: 22-12 AWG
Working Frequency: 433.92MHz
Channel: 1CH
Control Modes: Self-locking, Momentary, Interlocking
Static Current: ≤6mA
Maximum Load Current: 30A / each channel
Operating Temperature: -20 ° C to +70 ° C
PCB size: 90mm x 59mm x 18mm
Case size: 100mm x 68mm x 50mm
Transmitter:
Model No.: 0021000 (C-1) / 0021001 (C-2)
With Sliding Cover: Slide up when it doesn’t work (to protect the button). Slide down the button will appear.
Channel/Button: 1 (C-1) / 2 (C-2)
Button Symbol: No symbol (C-1) / 1, 2 (C-2)
Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months)
Operating Current: 6mA
Operating Frequency: 433Mhz
Encoding Chip: PT2262/ PT2264/ SC2262
Encoding Type: Fixed code by soldering, up to 6561 codes.
Transmitting Distance: 100m / 300ft (theoretically)
Modulation Mode: ASK
Unit Size: 58mm x 39mm x 16mm
Matching Transmitters:
The receiver can work with different transmitters, such as model C-1
/ C-2 (100M), CWB-1 / CWB-2 (50M, waterproof), or CB-1 / CB-2
(1000M) etc.
When you set the receiver in Self-locking or Momentary mode, it
should work with single button transmitter, such as model C-1
(100M), CWB-1 (50M, waterproof), or CB-1 (1000M) etc. When you set
the receiver in Interlocking mode, it should work with two buttons
transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), or
CB-2 (1000M) etc.
Working Range:
With a transmitter (such as C-1) to form a complete set, the maximum
working distance can reach 100M in an open ground.
The maximum working distance is a theoretical data, it shall be
operated in an open ground, no barriers, no any interference. But in
the practice, it will be hindered by trees, walls or other
constructions, and will be interfered by other wireless signals.
Therefore, the actual distance may not reach this maximum working
distance.
If you want to have a further working range, you can use a powerful
transmitter, such as CB-1 or CB-2 transmitter.
Usage (with the transmitter C-1 or C-2):
The receiver can be used to control both DC 0~28V and AC 110~240V
equipments.
Notice: The receiver is dry relay output, not DC/AC power output.
Initial state of relay output terminals: Terminals B and C are
Normally Open; Terminals A and C are Normally Closed.
Wiring:
1) If you want to control a DC 12V lamp, do as following:
1.1 Connect the positive pole of DC power supply to terminal “L / +”
of INPUT, and connect the negative pole of DC power supply to
terminal “N / −” of INPUT.
1.2 Connect terminal B to the positive pole of DC power supply,
connect terminal C to the positive pole of DC lamp, and connect the
negative pole of DC lamp to the negative pole of DC power supply.
2) If you want to control an AC 220V lamp, do as following:
2.1 Connect the positive pole of DC power supply to terminal “L / +”
of INPUT, and connect the negative pole of DC power supply to
terminal “N / −” of INPUT.
2.2 Connect terminal B to the live wire of AC power supply, connect
terminal C to one side of AC lamp, and connect another side of AC
lamp to the neutral wire of AC power supply.
Setting different control modes:
We have set the receiver as Self-locking control mode before
delivery. If you want to use other control modes, do as following
operation:
1) Setting Self-locking mode: Only connect Jumper-2.
Mode Self-locking (working with transmitter C-1): Press -> On; Press
again -> Off.
Press the button of the transmitter: The relay is activated (connect
the terminals B and C, disconnect the terminals A and C), and the
lamp is turned on.
Press the button again: The relay is deactivated (disconnect the
terminals B and C, connect the terminals A and C), and the lamp is
turned off.
2) Setting Momentary mode: Only connect Jumper-1.
Mode Momentary (working with transmitter C-1): Press and hold -> On;
Release -> Off.
Press and hold button of the transmitter: The relay is activated
(connect the terminals B and C, disconnect the terminals A and C),
and the lamp is turned on.
Release the button: The relay is deactivated (disconnect the
terminals B and C, connect the terminals A and C), and the lamp is
turned off.
3) Setting Interlocking mode: Disconnect Jumper-1 and Jumper-2.
Mode Interlocking (working with transmitter C-2): Press -> On; Press
another button -> Off.
Press button 1 of the transmitter: The relay is activated (connect
the terminals B and C, disconnect the terminals A and C), and the
lamp is turned on.
Press button 2 of the transmitter: The relay is deactivated
(disconnect the terminals B and C, connect the terminals A and C),
and the lamp is turned off.
Wired control terminals:
The receiver has wired control terminals, and you can connect
external devices, sensors, or manual switches to the receiver's
manual terminals, then use them to trigger the receiver.
1) By low level signal:
You can connect external devices (with low level output signal) to
manual terminal 1 (Signal−), and terminal 2 (Signal+), then the
external device’s output signal can control the receiver.
When the external device outputs low level signal to manual terminal
1 and terminal 2, the relay is activated (connect the terminals B
and C, disconnect the terminals A and C), and the lamp is turned on.
When the external device stops to output signal, the relay is
deactivated (disconnect the terminals B and C, connect the terminals
A and C), and the lamp is turned off.
2) By NO/NC contact:
You can connect manual switches to manual terminals 1 and 2, then
you can use manual switches to control the receiver.
When connect terminals 1 and 2, the relay is activated (connect the
terminals B and C, disconnect the terminals A and C), and the lamp
is turned on.
When disconnect terminals 1 and 2, the relay is deactivated
(disconnect the terminals B and C, connect the terminals A and C),
and the lamp is turned off.