This 2 channel wireless remote control momentary on off switch is widely applied to control on off electrical devices such like lights, motors, fans, electrically operated doors / locks / windows / blinds, etc. It has the characteristics of reverse power protection and over current protection. It uses microcontroller model of EM78P156, an 8-bit microprocessor designed and developed with low-power and high-speed CMOS technology. There are three working voltages DC9V, DC12V and DC24V to choose from. Available transmitting frequencies include 315MHz and 433MHz.
Feature: Application:
It can be used in industry automation, agriculture automation and home
automation, such as factory, house, farm, pasture, vehicle, ship, offshore
operation, aerial vehicle, field call, etc. It can remote control equipments on
land, water and air, such as remote control lights, sirens, locks, motors,
fans, winches, blinds, linear actuators, doors, windows, electric solenoid
valves, security alarm, business signs and various devices. Wireless control, easy
to install. Relay
Output: This receiver is relay output, it can be used to operate both DC and AC
equipments. The terminals are NO / NC (normally open / normally closed), which
serves as a switch. That means you should also connect a separate power supply
to equipments. You can
turn on/ off the receiver with transmitter (remote control) from any place
within a reliable distance. Wireless RF
signal can pass through walls, floors, doors or windows. With
reverse power protection and over current protection. Reliable
control: The receiver only works with the transmitter which use same code. One/several
transmitters can control one/several receivers simultaneously. You can use
two or more units in the same place. Receiver Parameters: Model No.: S2L-DC06-ANT1 / S2L-DC09-ANT1 / S2L-DC12-ANT1
/ S2L-DC24-ANT1 Power Supply
(Operating Voltage): DC6V (S2L-DC06-ANT1), DC12V±1V
(S2L-DC12-ANT1), DC9V±1V (S2L-DC09-ANT1), DC24V±1V (S2L-DC24-ANT1) Output: Relay output
(Normally open and normally closed) Working Voltage Range
of Relay: AC110~240V or DC0~28V Working Frequency:
315MHz / 433MHz Channel: 2 CH Control Modes: Latched
(Press -> On, another relay Off; Press another button -> Off) Static Current: ≤6mA Maximum Working
Current: 10A / each channel PCB size: 67mm x 50mm
x 18mm Case size: 75mm x 54mm x 27mm Work with Fixed code transmitters or Learning code transmitters. Matching Transmitters: The
receiver can work with different transmitters, such as model C-3 (100M), CWB-3
(50M, waterproof), or CB-3 (1000M) etc. Working
Range: With a transmitter (such as C-3) to form a complete set, the
maximum working distance can reach 200M in an open ground. The maximum working
distance is a theoretical data, it shall be operated in an open ground, no
barriers, no any interference. But in the practice, it will be hindered by
trees, walls or other constructions, and will be interfered by other wireless
signals. Therefore, the actual distance may not reach this
maximum working distance. If you
want to have a further working range, you can install an external antenna to
the receiver, and you also can use a powerful
transmitter, such as CB series transmitters. Telescopic Antenna: Length of external telescopic antenna: 80mm / 305mm (stretch) If you
stretches the external telescopic antenna, it can have a further working range. Usage: The receiver can be used to control both DC 0~28V and AC 110~240V
equipments. Notice: The receiver is relay output, not DC/AC power output. Initial
state of relay output terminals: Terminals B and C are Normally Open; Terminals
A and B are Normally Closed. Wiring: If you want to control a DC 12V lamp, do as following: 1) Connect the positive pole of DC power supply to terminal “+”, and
connect the negative pole of DC power supply to terminal “-”. 2) Connect terminal C to the positive pole of DC power supply, connect terminal
B to the positive pole of DC lamp, and connect the negative pole of DC lamp to
the negative pole of DC power supply. If you want to control an AC 220V lamp, do as following: 1) Connect the positive pole of DC power supply to terminal “+”, and
connect the negative pole of DC power supply to terminal “-”. 2) Connect terminal C to the live wire of AC power supply, connect terminal
B to one side of AC lamp, and connect another side of AC lamp to the neutral
wire of AC power supply. Operating (with the transmitter C-3): Press
button C: Turn on relay 1 (connect B and C,
disconnect A and B), the lamp 1 is on. Turn off relay 2 (disconnect B and C, connect A and B), the lamp 2 is off. Press
button B: Turn on relay 2 (connect B and C,
disconnect A and B), the lamp 2 is on. Turn off relay 1 (disconnect B and C, connect A and B), the lamp 1 is off. Press
button A: Turn off relay 1&2 (disconnect B and C,
connect A and B), the two lamps are off. How to pair
the transmitter to the receiver: 1) Press
the learning button of receiver for 1- 2 seconds; signal LED on the receiver is
on. The receiver enters into status of LEARNING. 2) Press
any one button on transmitter. If signal LED flashes quickly 15 times and turns
off, it means learning is successful. 3) When
receiver is in the status of LEARNING, press again the learning button, signal
LED turns off, learning process will be discontinued. 4) The
receiver can learn several remote controls with different codes. Delete all transmitters: We have
learned remote control to the receiver. If you don’t want the receiver to work
with the remote control, you can delete all codes of remote controls, which are
stored in the receiver.
Operation:
Press and hold the learning
button of receiver until signal LED flashes slowly; release the button, LED
keeps slow flash. That means all stored codes have been deleted successfully.
